RE: Linksys WRT54G - Advice for european users

• Previous message: Daniel Fabian: "PHP escapeshellarg Windows Vulnerability"
• Maybe in reply to: Christer Palm: "Linksys WRT54G - Advice for european users"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

To: 'Richard Bjerregaard' <bjerregaard@jyde.dk>, bugtraq@securityfocus.com
Date: Wed, 9 Jun 2004 15:54:54 -0400 

The readme on the v2.07 US firmware (for v2 hardware) carries no such
warning... Apparently they pay more attention to things like this in
Europe! :)

Actually, since my initial problems a few months back - just last week in
fact - they released another version of 2.07 for the v1.1 hardware... The
readme in _that_ zip file mentions that you must be running 1.09.1 on v1.0 /
v1.1 hardware or the install won't work. But, if you get the other 2.07
firmware - the one that has been available for some time now - all you get
is the claim that it supports all versions of the WAP54G hardware, and no
other warnings:

Version 2.07, April 28, 2004
- Adds Linksys Wireless Guard support
Note:WPA does not work in Wireless Bridge/Repeater mode in this release

Version 2.06, December 16, 2003 (ver.2 initial release)
- Updated User Interface format and layout
- Updated wireless driver to support all versions of WAP54G hardware
- Adds AP Client Mode
- Adds Wireless Repeater Mode for WAP54G and WRT54G (requires fw 2.02.2 or
above)
Note:WPA does not work in Wireless Bridge/Repeater mode in this release

http://www.linksys.com/download/vertxt/wap54gv2_fw_ver207.txt

But thank you to everyone who pointed out this document -
http://www.linksys.com/download/vertxt/WAP54GupgradeprocedureV2.doc - It
definitely was information that helped...

-----Original Message-----
From: Richard Bjerregaard [mailto:bjerregaard@jyde.dk]
Sent: Tuesday, June 08, 2004 6:15 PM
To: bugtraq@securityfocus.com
Cc: Connor, Ethan M. W
Subject: Re: Linksys WRT54G - Advice for european users

Hejsa Ethan

7. juni 2004, 18:56:18, you wrote:

CEMW> Another bit of warning about linksys and their inability to get
CEMW> the firmware release vs. hardware version worked out correctly.
CEMW> If you install the latest WAP54G firmware update for the v2
CEMW> hardware on v1 or v1.1 hardware (which the readme says is
CEMW> supported)... Expect the ethernet port to disable itself (due to
CEMW> the order in which the interfaces are initialized on the
CEMW> device) after you power cycle it...

From the readme.txt
"
Note: If you try and upgrade an older unit to firmware 2.07 without
upgrading the firmware to 1.09.1 prior to upgrade, you may damage the Access
Point."

Checkout these links

http://www.linksys.com/international/firmware.asp?intfwid=9&coid=48

This document explains how to upgrade your WAP54G to firmware version
2.07.01 The procedure applies to V1.0 and V1.1 hardwares.
http://www.linksys.com/download/vertxt/WAP54GupgradeprocedureV2.doc

-- 
Best regards/Venlig hilsen
Richard Bjerregaard
This message and any included attachments is intended for the sole use of
the individual or entity to whom it is addressed. The information contained
herein is confidential, proprietary or privileged and may be subject to
protection under law. You are notified that unauthorized use, distribution,
review or reproduction of such information is strictly prohibited and may
subject you to criminal or civil penalties. If you have received this
transmission in error, please promptly delete it and notify the sender by
e-mail with a copy to 'postmaster@hendersonbrothers.com'.

• Previous message: Daniel Fabian: "PHP escapeshellarg Windows Vulnerability"
• Maybe in reply to: Christer Palm: "Linksys WRT54G - Advice for european users"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]