Re: A question about ssh RSA key connection



Thanks ming for your reply

When I connect to 47.154.169.130 the from ip would be
47.154.169.130, but when I try to connect to other servers, the from
ip became 47.154.169.128, so this is really refusing me.



2009/8/24 ming.zym@xxxxxxxxx <ming.zym@xxxxxxxxx>:
this is far from a ssh problem, as the connect src address is selected
by system, mostly by the default routing set, in your case, there are
many IP in the same vlan/ip space, that will be choosed to be the first
ip in your ip list, .130 is the first then.

you may use the "-b" option if you really need to set your src ip
address.


在 2009-08-22六的 12:10 +0800,徐广写道:
Hi
I recently met with a problem when trying to set up ssh connection
through the ssh key

I first create a key through command ssh-keygen -t rsa -f
/.ssh/pmcftp_id_rsa -P "" , two files would be created under /.ssh
pmcftp_id_rsa and pmcftp_id_rsa.pub, then I insert an entry into the
.pub file - from="47.154.169.129,47.154.169.128" this should
restrickt that the ssh key should only work for sources of these two
ips.
Then I push the public key to another server under ~pmcftp/.ssh, after
that, I start the ssh connection through command ssh -I pmcftp -i.
./ssh/pmcftp_id_rsa <server ip>, the ssh connection would be set up
without asking for the passwd.
But, when I create the ssh key on a server that has several ip
address, like following:
=====
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu
8232 index 1
inet 127.0.0.1 netmask ff000000
uplink0: flags=1040863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST,DEPRECATED,IPv4>
mtu 1500 index 2
inet 47.154.169.130 netmask ffffff00 broadcast 47.154.169.255
ether 0:0:bb:2e:74:e
uplink0:1: flags=1000863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST,IPv4>
mtu 1500 index 2
inet 47.154.169.128 netmask ffffff00 broadcast 47.154.169.255
uplink0:2: flags=1000863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST,IPv4>
mtu 1500 index 2
inet 47.154.169.129 netmask ffffff00 broadcast 47.154.169.255
uplink1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.47.1 netmask ffffff00 broadcast 192.168.47.255
ether 0:0:bb:2e:74:d
=====
And added ip 47.154.169.128 and 47.154.169.129 into the from ip list
entry in the key file, then I push the ssh key to server
47.154.169.130 (which should be the same server as the source)
Then when I try to start the ssh connection through command ssh -I
pmcftp -i. ./ssh/pmcftp_id_rsa 47.154.169.130 , the key does not work
anymore, and the log give info like this
==
Authentication tried for pmcftp with correct key but not from a
permitted host (host=iems196-unit0, ip=47.154.169.130)
==
Obviously, here the from ip list does not include 47.154.169.130, and
the ssh connection treate the from ip as 47.154.169.130 not other ips
of this server.
Then I tried another command
Ssh -b 47.154.169.128 -I pmcftp -i. ./ssh/pmcftp_id_rsa
47.154.169.130 the key works well again.
The -b option is binding the from ip to 57.154.169.128 and it's in the
from ip list in the key file.

how the ip of the from side of the ssh connection is obtained? When
the from side of the ssh connection has several ips how would the ip
address be determined by the to side?
Any info would be highly appreciated, thanks in advance!

Best regards
Guang

--
徐广
13581797776





--
徐广
13581797776



Relevant Pages

  • Re: Secure Postgres access
    ... I would like to access a remote Postgres server from a Python program in a ... Both Postgres and the Python program are running on Linux. ... you put their pubkey in authorized_keys on the server for SSH connection. ...
    (comp.lang.python)
  • Remote Login using SSH tunnel with XP
    ... establish an ssh connection with an tunnel for an terminal ... We have a new installed windows 2003 ... terminal server, previous times we used citrix terminal ... employees are not very happy with the current situation. ...
    (microsoft.public.windowsxp.work_remotely)
  • Remote Login using SSH tunnel with XP
    ... establish an ssh connection with an tunnel for an terminal ... We have a new installed windows 2003 ... terminal server, previous times we used citrix terminal ... employees are not very happy with the current situation. ...
    (microsoft.public.windowsxp.help_and_support)
  • Remote connection using ssh tunnel and XP
    ... establish an ssh connection with an tunnel for an terminal ... We have a new installed windows 2003 ... terminal server, previous times we used citrix terminal ... employees are not very happy with the current situation. ...
    (microsoft.public.windowsxp.network_web)
  • A question about ssh RSA key connection
    ... I recently met with a problem when trying to set up ssh connection ... I start the ssh connection through command ssh -I pmcftp -i. ... inet 47.154.169.130 netmask ffffff00 broadcast 47.154.169.255 ...
    (SSH)