RE: [fw-wiz] pix firewall config quest

From: Ahmed, Balal (balal.ahmed_at_cgey.com)
Date: 08/13/03

  • Next message: Steve Saeedi: "Re: [fw-wiz] PIX 6.3.2 Upgrade?" 
    To: "'Don Burgess'" <don_burgess@hotmail.com>, firewall-wizards@honor.icsalabs.com
Date: Wed, 13 Aug 2003 15:48:03 +0100

    static (inside,outside) tcp 10.10.1.208 3000 192.168.1.10 3000 netmask
    255.255.255.255

    -----Original Message-----
    From: Don Burgess [mailto:don_burgess@hotmail.com]
    Sent: 07 August 2003 08:44
    To: firewall-wizards@honor.icsalabs.com
    Subject: [fw-wiz] pix firewall config quest

    sorry for this being such a basic question, but i am using a PIX to learn,
    and i am trying to fingure out how to forward a port from the incoming
    interface to a internal ip..

    here is the basic scenario
    pix 506e
    internal pat 192.168.1.0
    external interface address in my test setup is 10.10.1.208
    internal ip that i want to access the port of 192.168.1.10
    port that i want to access 3000

    any help in the config to use would be GREATLY appreciated

    _________________________________________________________________
    MSN 8 with e-mail virus protection service: 2 months FREE*
    http://join.msn.com/?page=features/virus

    _______________________________________________
    firewall-wizards mailing list
    firewall-wizards@honor.icsalabs.com
    http://honor.icsalabs.com/mailman/listinfo/firewall-wizards

    ********************************************************************************************
    " This message contains information that may be privileged or confidential and
    is the property of the Cap Gemini Ernst & Young Group. It is intended only for
    the person to whom it is addressed. If you are not the intended recipient, you
    are not authorized to read, print, retain, copy, disseminate, distribute, or use
    this message or any part thereof. If you receive this message in error, please
    notify the sender immediately and delete all copies of this message ".
    ********************************************************************************************

    _______________________________________________
    firewall-wizards mailing list
    firewall-wizards@honor.icsalabs.com
    http://honor.icsalabs.com/mailman/listinfo/firewall-wizards

  • Next message: Steve Saeedi: "Re: [fw-wiz] PIX 6.3.2 Upgrade?"

    Relevant Pages

    • [fw-wiz] pix firewall config quest
      ... sorry for this being such a basic question, but i am using a PIX to learn, ... and i am trying to fingure out how to forward a port from the incoming ... external interface address in my test setup is 10.10.1.208 ...
      (Firewall-Wizards)
    • Re: Open port PIX 501
      ... :i can't open the port in my PIX. ... :I need open the port 1000 to point to the IP 10.254.254.222. ... in practice only DNS servers doing zone transfers need tcp. ... of UDP, it would be a highly unusual client which did not stick ...
      (comp.dcom.sys.cisco)
    • Re: Testing A Cisco PIX 501
      ... and it uses let's say 53 DNS port or HTTP 80 port ... Optionally write a test bench. ... I would like to, for example, be safer from trojans. ... my PIX, my PC is also cabled to the PIX and my wireless router is also ...
      (comp.security.firewalls)
    • RE: [fw-wiz] ? re: PIX port translation config
      ... however inorder to perform the port mapping you need to use the following ... Also make sure you do not have 'sysopt noproxyarp dmz' defined or the pix ... wont proxy arp on that interface. ... > and need assistence with the config. ...
      (Firewall-Wizards)
    • Re: Allowing icomming connections?
      ... >I am suspecting that one of my users is allowing an Internet IP Addy ... I see many of the below lines (PIX log) where the UDP ... Port on C.C.C.C remains constant as well, ... ports on A.A.A.A increment and that that tells you "that NAT remains active". ...
      (comp.dcom.sys.cisco)